FOC-Based Soft Start of Induction Motors Using Trigonometric S-Curve

DOI: https://doi.org/10.52549/ijeei.v13i3.6656
Published: 10-08-2025 • Issue: Vol. 13 No. 3: September 2025 • Section: Regular paper

Abstract

This paper presents a novel approach to improving the starting performance of three-phase induction motors by integrating an optimized S-curve acceleration profile based on trigonometric functions into a Field-Oriented Control (FOC) framework. Unlike conventional third- and fifth-order polynomial trajectories that suffer from limited jerk continuity and insufficient mechanical damping, the proposed method ensures smooth transitions in acceleration and jerk using sinusoidal functions. The core contribution of this work lies in the development and application of a second-order continuous trigonometric velocity trajectory that significantly reduces mechanical shocks and current oscillations during motor startup and stop phases. Furthermore, the method is designed for real-time implementation on FPGA hardware, enabling high-resolution pulse-width modulation (PWM) suitable for embedded motion control systems. Simulation and experimental results demonstrate superior motion smoothness, improved torque tracking, and enhanced mechanical reliability compared to traditional methods. This research provides a practical and effective solution for applications requiring precise soft-start/stop capabilities, particularly in elevator systems and other high-performance industrial drives.


References

H.-G. H. Mirza Abdul Waris Begh, “Comparison of Field Oriented Controland Direct Torque Control,†no. March 2018, pp. 1–16, 2018, doi: 10.36227/techrxiv.171332371.13141782/v1.

Lê Thị Thu Phương, Lê Thị Thu Huyá»n, Phạm Thị Hồng Anh, “Ứng dụng Ä‘iá»u khiển vector tá»±a từ thông rotor cho động cÆ¡ không đồng bá»™,†Tạp chí khoa há»c và Công nghệ, vol. 172, no. 1, pp. 115–119, 2017.

L. T. H. Bui Van Vu, Vo Phuong, DO Van Can, “A survey of working models of direct current motor in PWM rectifier – separately excited direct current motor system,†Journal of Science, Quy Nhon University, vol. 15, no. 5. pp. 75–85, 2021. doi: 10.52111/qnjs.2021.15508.

T. V. T. Äá»— Văn Cần, “Äá» xuất Ä‘iá»u khiển vị trí giảm nhiá»…u Ä‘a kênh (ADRC) trên FPGA cho hệ truyá»n đông Servo,†Tạp chí khoa há»c trưá»ng Äại há»c Quy NhÆ¡ntrưá»ng Äại há»c Quy NhÆ¡n, vol. 12, no. 3, pp. 91–102, 2018.

Do Van Can, “Current controller design based on FPGA,†J. Sci. - Quy Nhon Univ., vol. 15, no. 1, pp. 71–78, 2020.

K. Sabahi, M. Teshnehlab, and M. A. shoorhedeli, “Recurrent fuzzy neural network by using feedback error learning approaches for LFC in interconnected power system,†Energy Conversion and Management, vol. 50, no. 4. pp. 938–946, 2009. doi: 10.1016/j.enconman.2008.12.028.

A. Guellal, C. Larbes, D. Bendib, L. Hassaine, and A. Malek, “FPGA based on-line Artificial Neural Network Selective Harmonic Elimination PWM technique,†Int. J. Electr. Power Energy Syst., vol. 68, pp. 33–43, 2015, doi: 10.1016/j.ijepes.2014.11.030.

H. Bai, C. Liu, E. Breaz, and F. Gao, “Artificial neural network aided real-time simulation of electric traction system,†Energy AI, vol. 1, Aug. 2020, doi: 10.1016/j.egyai.2020.100010.

N. C. N. Dao Huynh Dang Khoa, Su Hong Thanh, “Intelligent control of induction motor using recurrent fuzzy neural networks,†TNU J. Sci. Technol., vol. 227, no. 08, pp. 46–55, 2022.

B. Kumar, P. Wang, and A. S. Hossain, “Design of Motion Profile of Stepper Motor for Elevator Using Arduino Uno,†North Am. Acad. Res. J., vol. 3, no. 04, pp. 683–695, 2020, [Online]. Available: https://doi.org/10.5281/zenodo.3764537

A. Drumea, C. I. Marghescu, M. P. Ă, G. Jitianu, and A. Vlad, “S-curve motion control implementation using 32-bit microcontroller,†in Proceedings of 2022 International Conference on Hydraulics and Pneumatics - HERVEX November 9-10, Băile Govora, Romania, 2022, pp. 160–165.

Z. Zhang and Y. Yu, “S-type speed control curve based on the number of pulses,†J. Phys. Conf. Ser., vol. 2196, no. 1, 2022, doi: 10.1088/1742-6596/2196/1/012038.

V. Kombarov, V. Sorokin, O. Fojtů, Y. Aksonov, and Y. Kryzhyvets, “S-curve algorithm of acceleration/deceleration with smoothly-limited jerk in high-speed equipment control tasks,†MM Sci. J., vol. 2019, no. November, pp. 3264–3270, 2019, doi: 10.17973/MMSJ.2019_11_2019080.

C. Li and F. Chen, “Application of S-curve Acceleration and Deceleration in Winding of Bond-Wire,†Int. J. Trend Res. Dev., vol. 8, no. 4, pp. 158–161, 2021.

M. A. Fayrouz Allam, Zaki Nossair, Hesham Gomma, Ibrahim Ibrahim, “Evaluation of Using a Recurrent Neural Network (RNN) and a Fuzzy Logic Controller (FLC) In Closed Loop System to Regulate Blood Glucose for Type-1 Diabetic Patients,†I.J. Intell. Syst. Appl., vol. 10, pp. 58–71, 2012.

Äá»— Văn Cần, “Nghiên cứu thiết kế bá»™ Ä‘iá»u khiển cho hệ truyá»n động Servo,†Tạp chí Khoa há»c Trưá»ng Äại há»c Cần ThÆ¡, vol. 2, no. X, 2016.

X. Li, “Optimizing S-curve Velocity for Motion Control,†J. Appl. Math., no. FEBRUARY 2010, pp. 1–12, 2010.

X. Wei, “Acceleration and deceleration control design of step motor based on TMS320F240,†Procedia Eng. Elsevier, vol. 15, pp. 501–504, 2011, doi: 10.1016/j.proeng.2011.08.095.

V. I. Vlachou, D. E. Efstathiou, and T. S. Karakatsanis, “Design, Analysis and Application of Control Techniques for Driving a Permanent Magnet Synchronous Motor in an Elevator System,†Machines, vol. 12, no. 8, 2024, doi: 10.3390/machines12080560.

R. Akçelik and M. Besley, “Acceleration and deceleration models,†Springer Ser. Adv. Manuf., no. January 2001, pp. 107–156, 2008, doi: 10.1007/978-1-84800-336-1_4.

M. Osama and O. Abdul-Azim, “Implementation and performance analysis of an elevator electric motor drive system,†2008 12th Int. Middle East Power Syst. Conf. MEPCON 2008, pp. 114–118, 2008, doi: 10.1109/MEPCON.2008.4562368.

G. Cimini, G. Ippoliti, G. Orlando, and M. Pirro, “PMSM control with power factor correction: Rapid prototyping scenario,†Int. Conf. Power Eng. Energy Electr. Drives, no. May 2013, pp. 688–693, 2013, doi: 10.1109/PowerEng.2013.6635693.

M. Konuhova, “Modeling of Induction Motor Direct Starting with and without Considering Current Displacement in Slot,†Appl. Sci., vol. 14, no. 20, 2024, doi: 10.3390/app14209230.

E. S. T. Ralph P. Hervilla, Ruben H. Habaña, Zumel Cadenas, Salem Joh P. Suelon, “Advancements in Three-Phase Electric Motor Control: The Dual Voltag Motor Controller for Seamless Voltage Switching and Enhanced Efficiency,†J. Adv. Zool., vol. 44, pp. 1770–1780, 2023.

N. P. Q. Do Van Can, Doan Quang VInh, “Nghiên cứu nâng cao chất lượng gia công máy công cụ nhỠbộ tăng giảm tốc có cấu trúc linh hoạt trên SoCFPGA,†in Cơ kỹ thuật và tự động hoá, 2016.

K. D. Nguyen, T. C. Ng, and I. M. Chen, “On Algorithms for Planning S-Curve Motion Profiles,†Int. J. Adv. Robot. Syst., vol. 5, no. 1, pp. 99–106, 2008, doi: 10.5772/5652.

A. Gavai, A. Kasbekar, and A. V. Mulay, “Position Control of BLDC Motor Using S-Curve for Trajectory Planning and Feedforward Control Design,†2019 10th Int. Conf. Comput. Commun. Netw. Technol. ICCCNT 2019, no. July 2019, pp. 1–6, 2019, doi: 10.1109/ICCCNT45670.2019.8944914.

A. Gastli and M. M. Ahmed, “ANN-based soft starting of voltage-controlled-fed IM drive system,†IEEE Trans. Energy Convers., vol. 20, no. 3, pp. 497–503, 2005, doi: 10.1109/TEC.2004.841522.

R. M. Larik, U. Humayun, and M. Rashid, “Enhancing Three-Phase Induction Motor Performance with Soft Ramp Control,†Int. J. Innov. Sci. Technol., no. December, 2024.

A. A. Menaem, S. Beryozkina, and M. Safaraliev, “Intelligent current-speed soft-starting controller for an induction motor drive system,†J. Energy Syst., vol. 8, no. 4, pp. 221–236, 2024, doi: 10.30521/jes.1533403.

D. Y. Yang, Y. S. Kim, T. H. Oh, S. H. Lee, and D. Il Cho, “Closed-Loop Soft Starter Firing Angle Control Method Using only Current Feedback,†IEEE Access, vol. 12, pp. 112062–112073, 2024, doi: 10.1109/ACCESS.2024.3441250.

H. Chen and C. Bi, “Optimal starting frequency of three-phase induction motor,†IET Electr. Power Appl., vol. 16, no. 3, pp. 362–369, 2022, doi: 10.1049/elp2.12159.

D. Van Can and T. X. Khoa, “Research design position controller based on FPGA,†Há»™i nghị - Triển lãm quốc tế lần thứ 7 vá» Äiá»u khiển và Tá»± động hoá, pp. 109–115, 2024.

Author Biographies

Do Van Can

Do Van Can: https://orcid.org/0009-0000-6599-2221. Born in 1981, received a Master’s degree in Automation in 2009 and a Ph.D. degree in 2019 from the University of Danang. Since 2004, he has been a lecturer at the Faculty of Engineering and Technology, Quy Nhon University. His research interests include chip design, FPGA, SoC, electric machine control, CNC machine tools, industrial networks, and SCADA systems. Phone: +84 935 253 630 | Email: dovancan@qnu.edu.vn


Hoang Van Hieu
Hoang Van Hieu: https://orcid.org/0009-0007-2517-9229. Born in 1983, obtained an engineering degree in Electrical Engineering Technology in 2012. Currently, he is a graduate student (Class K26A) in Electrical Engineering at Quy Nhon University. Since 2012, he has been a lecturer at Kon Tum Vocational School, now known as Kon Tum College. He teaches subjects related to his field of expertise, such as Electric Machines, Electrical Equipment, and Electrical Installation Techniques. Phone: +84 961 164 679 | Email: hieuhoang83vn@gmail.com

How to Cite

[1]
D. V. Can and H. Van Hieu, “FOC-Based Soft Start of Induction Motors Using Trigonometric S-Curve”, IJEEI, vol. 13, no. 3, pp. 536–547, Aug. 2025, doi: 10.52549/ijeei.v13i3.6656.